Wolf CT36G/P Manuel d'utilisateur télécharger pdf

The Wolf Warming Drawer Model

WD30 can be installed above or

below a single wall oven SO30F/S,

SO30U/B, SO30U/P or SO30U/S or

below a cooktop CT36E/S, CT36E/B,

CT36E/P, CT36G/S, or CT36G/P.

Please refer to installation instructions

provided with cooktops for additional

installation information.

The Wolf Warming Drawer can also

be installed next to or above another

Wolf Warming Drawer.

IMPORTANT NOTE: This Front Panel Kit

is designed for and approved only for

use with Wolf Warming Drawer WD30.

• Integrated Front Panel Kit (802727)

Contains:

(1) Front Panel (802598)

(1) Condensation Trap (805553)

(2) Pem Nuts (805551)

(10) 8-18 x 3/8" Long Screws

IMPORTANT NOTE: Please read

these instructions carefully before

beginning installation. Follow all

applicable regulations and guidelines

specified in the Wolf Warming

Drawer Installation Guide that

accompanies the Wolf Warming

Drawer.

Install Warming Drawer:

IMPORTANT NOTE: There are

significant differences in the cabinet

requirements when installing a

Wolf Integrated Front with a Wolf

Warming Drawer. Overall cabinet

width and depth greatly impacted as

specifications are much different that

Warming Drawer with a Stainless Steel

front.

/16"

(691)

/2" (724)

OVEN ROUGH

OPENING WIDTH

(127)

(102)

/16"* (760)

ROUGH OPENING WIDTH

WARMING DRAWER

(127)

(102)

/2"min (648)

ROUGH OPENING DEPTH

WARMING DRAWER

33" (838)

CABINET WIDTH

26" (660)

CABINET DEPTH

NOTE: Dimensions in parentheses are in millimeters.

*Dimension may vary by

1/8" (3 mm).

/8"

(60)

2"(51) x 2"(51)

ANTI-TIP BLOCK

/8"*

(264)

/8"

(60)

/8"*

(264)

CABINET SIDE VIEW

Tools and Materials Required:

• Wood screws or other hardware for installing runners or shelf to sup-

port warming drawer and mount front support framing to cabinet

• 2" x 4" or 2" x 2"(51 x 102 or 51 x 51) lumber for runners

• 2" x 4" or 2" x 2"(51 x 102 or 51 x 51) wood block for anti-tip.

• Lumber for front support framing

• Decorative wood front panel

• Saw

• Level

• Drill and 1/16" bit

• Phillips screwdriver

W OLF W ARMING D RAWER I NTEGRATED F RONT P ANEL

K IT(802727) INSTALLATION I NSTRUCTIONS

Integrated Front Panel Panel Kit.qxd 10/10/2003 6:03 AM Page 1

1 2 3 4

Résumé du contenu

Page 1 - 1/8" (3 mm)

The Wolf Warming Drawer ModelWD30 can be installed above orbelow a single wall oven SO30F/S,SO30U/B, SO30U/P or SO30U/S orbelow a cooktop CT36E/S, CT3

Page 2 - CABINET FRONT VIEW

W OLF W ARMING D RAWER I NTEGRATED F RONTP ANEL K IT I NSTALLATION I NSTRUCTIONSRunners must be level, rigidlymounted and capable of supporting175 pou

Page 3 - Assembly

W OLF W ARMING D RAWER I NTEGRATED F RONTP ANEL K IT I NSTALLATION I NSTRUCTIONSInstallation Procedures:Step 1:• Install 2" x 4" or 2"

Page 4 - 804630 REV-A 10/03

Install Front Panel andCondensation Trap:1. Remove two mounting nuts fromWolf Warming Drawer door frontand discard nuts and lockwashers.DO NOT DISCARD